New Amada Marvel Model VT4555 (8 Mark ll) 18"X22" Vertical Tilt Frame Saw
New Machinery, Vertical SawNew Amada Marvel Model VT4555 (8 Mark ll) 18"X22" Vertical Tilt Frame Saw
Work Height | 22" |
Throat | 18" |
Power | 2 hp |
Blade Width | 1" |
Blade Length | 174" |
FPM | 450 |
SPECIFICATIONS & FEATURES
Rectangular Capacity Standard Capacity M6 High Column Capacity (Optional)
Blade at 90° 18” x 22” (457 mm x 560 mm) 18” x 28” (457 mm x 711 mm)
Blade at 45° 18” x 12.75” (457 mm x 324 mm) 18” x 17” (457 mm x 432 mm)
Speed Range 50 – 450 fpm (15 – 137 m/min) infinitely variable speed drive system.
Front-Mounted Speed Control Allows blade speed to be adjusted from operator’s
control station.
Feed Range 0 – 140 lbs. (64 kgf) infinitely variable direct reading scale balance
beam.
T-Slotted Worktable Work area 24.25” x 33” (616 mm x 838 mm)
Table height 34.5” (876 mm)
Four machined T-slots accept .625” (15.5 mm) T-Bolts.
Miter Cutting Column and blade tilt up to 45° right and left of vertical: work
always stationary. Built-in protractor.
Quick-Action Vise
Maximum opening 18” (457 mm).
Jaws can be shifted to either right or left side of blade. Jaws are 6” (152 mm) high, 12” (305 mm) wide.
Saw Feed Stops
Adjustable stops can be pre-set to stop advance of the saw head and return of blade
and to stop motor at any location within the 18” (457 mm) travel of
the blade.
Coolant System Built in with Flood system,
available with added optional drop
lubrication system. (Requires compressed air connection - Option Code ML2).
Controlled by on-off selector switch at operator’s station.
Tank capacity 21 gallons
(79 liters).
Flushing Hose Washes chips from hard-to-get-at places reducing clean-up time.
Power Chip Brush Together with blade wipers and flood coolant keep blade teeth free
of chips.
Carbide Guide System Guides are stationary and can be rotated to present new guiding
surface to the blade. Upper and lower guides have preloaded carbide-faced back-up
blocks to support back edge of the blade.
Blade 14' 6" (4420 mm) long x 1" (25 mm) wide, .035" (89 mm) thick.
One Welded-Edge Band Blade is furnished with each machine.
Motors Main; 5 H.P. (3.75 kW), 1800 RPM, totally enclosed fan cooled.
Coolant Pump: 1/8 H.P. (.1 kW) totally enclosed motor-built-in integrally.
Available voltage: 208-volt, 230 volt, 460, 3-phase.
Controls IEC fused disconnect switch and magnetic motor starters, with overload and
low voltage protection. Disconnect is NFPA79 compliant. Transformer provides low
voltage control
(120 Volts) to all push buttons at operator’s control panel and machine lighting
circuits.
Electrical and control components mounted in a NEMA 12 compartment. Electrical
Panel is UL labeled #E56388.
OPTION DESCRIPTIONS
Product Short Description Product Description
VT4555
(8-Mark-II) Metal Cutting Band Saw ALL-MECHANICAL, UNIVERSAL, METAL CUTTING,
BANDSAW MACHINE
Marvel Classic Color Scheme Also available in “Marvel Classic” color scheme for
additional charge (see options sheet).
Blade Eagle Beak VTR Eagle Beak VTR blade 14' 6" long x 1" wide, 3/6 tooth pitch.
This is the standard blade that is included with machine purchase, and you have the
option to order more. Note: if M6 High Column option is selected blade price needs
to be adjusted.
M6 High Column Column 6” (150 mm) longer than standard, providing increased
vertical capacity to 28” (712 mm) at vertical position and 17” high at 45 degrees.
High frame machines require a 15’ 6” (4724 mm) blade.
E4 Second Standard Vise set including 6” high x 12” wide (152 mm x 305 mm)
jaws and clamping hardware.
PERMITS MITER CUTTING.
M7 High Jaws 10” high x 12” wide (254 mm x 305 mm) in place of standard
jaws provided with machine. Jaws use same clamping hardware provided with machine.
DO NOT PERMIT MITER CUTTING.
M8 45° High Jaws In place of standard jaws provided with machine. Jaws use
same clamping hardware provided with machine. One Front Jaw and one Rear Jaw,
both mitered 45°, 10” high x 12” wide.
E5 High Jaw Vise- Complete High jaw set including 10” high x 12” wide
(542 mm x 305 mm) jaws and clamping hardware. DOES NOT PERMIT MITER CUTTING.
E6 High Jaws - Jaws Only 10” high x 12” wide (254 mm x 305 mm). Will
interchange with standard 6” high x 12” wide (152 mm x 305 mm). Jaws use same
clamping hardware provided with machine. DO NOT PERMIT MITER CUTTING.
E15 45° High Jaw Vise - COMPLETE includes one Front Jaw and one Rear Jaw,
both mitered 45°, 10” high x 12” wide (254 mm x 305 mm) and clamping hardware.
PERMITS MITER CUTTING.
E16 45° High Jaws Only Includes One Front Jaw and one Rear Jaw, both mitered
45°, 10” high x 12” wide (254 mm x 305 mm) for use where machine is already
equipped with clamping hardware.
PERMITS MITER CUTTING.
E14 Air power vise with machine. This can be used in place of the standard hand crank
ratchet nut. (Requires compressed air connection.)
M9A Variable Vise Pressure Controls and connections added to enable the machine
to operate with air controlled variable vise pressure for one or two vises and
utilizes the optional E14 (sold separately) air operated ratchet nut. PN: (8AB01288)
M17V 3° Canted Column (Standard Column) Modification of standard High Column
to add 3° forward approach angle, for increased efficiency in cutting of structural
materials. Changes horizontal capacity to 17”.
M17HV 3° Canted Column (High Column) Modification of standard High Column to add
3° forward approach angle, for increased efficiency in cutting of structural
materials. Note: Changes horizontal capacity to 16.75”.
SP2083 Optional High-Speed Modification
120 – 1080 fpm (36 – 329 m/min):
main motor changed to 10 H.P.,
totally enclosed, fan cooled.
Only available in 460-3-60-volt machine order.
ML2 Mist Lube - Automatic Drop Lubrication System. (Requires compressed air
connection 60-120psi)
ED2210 UnistCoolube
2210 Unist Coolube 2210 is the cutting oil and lubricant
that is shipped within your ML2 (Mist drop lubrication system). It is formulated as
a metal cutting oil and lubricant for metals, wood, rubber, and most plastics. It is
100% natural, non-toxic, non-staining, and will not oxidize (become sticky or leave a
residue).Coolube 2210 cutting fluid does not contain any ingredients currently
recognized as hazardous by OSHA, IARC or NIP. Coolube 2210 machining oil will never
cause dermatitis and is formulated from cosmetic grade raw materials,
which makes it entirely worker and environmentally safe. Coolube 2210 is a USDA
certified biobased product.
E8 Length Gauge For gauging work pieces from .062” to 10.5” (1.6 mm x 267 mm) long.
Fits T-slots in machine table.
8SP01337 Alignment Light Laser Projector for quick spotting of the cut.
MATERIAL HANDLING EQUIPMENT
8/F055 First Section Dead Roller Conveyor 5’ 0” (1524 mm) LONG, with five balls
bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, two stands,
one end stop, and mounting bracket. Used as first section on either loading or
discharge side of machine.
8/X055 Extension Dead Roller Conveyor 5’ 0” (1524 mm) LONG, five ball bearing
rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, one stand, attached
to an 8/F055, an SP1118, or another X055 for use on either loading or discharge side
of machine to extend the length of the roller tables needed.
SP1118 First Section Dead Roller Conveyor Free Standing 5’ 0” (1524 mm) LONG, with
five ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” centers, two stands,
and one end stop.
8/SP1040 First Section Dead Roller Conveyor with Manual Length Gauge 10’ 0” (3048 mm)
LONG, ten ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers,
includes Dead Stop, Tilting Type Gauge; manually operated.
Runs along tape and rail fastened to front side of Roller Table. Gauge can be locked
in place for gauging and tilted
out of the way to permit work passage. Indicate Left or Right configuration.
8/SP1097 Extension Dead Roller Conveyor with Gauge Rail 5’ 0” (1524 mm) LONG, five
ball bearing rollers, 2.5” (64 mm) diameter, spaced on 12” (305 mm) centers, like X055,
but also equipped with gauge rail and measuring tape extensions. For use with and as
an EXTENSION to SP1040. Indicate Left or Right configuration.
SUPPLEMENTARY MATERIAL HANDLING EQUIPMENT
E10 Length Gauge Manual light-duty length gauge. Securely mounts on roller
conveyor. Gauging limited by length of roller conveyor.
E11 Coolant Pan Will fit F055 and X055 roller conveyors. Collects and returns
coolant back to machine. Includes pan, V-trough, and hangers.
E12 Eccentric Lift Roller May be mounted on roller conveyor for either load or
discharge sides; manually operated to raise roller and material slightly above
machine table. Lift capacity 1,000 pounds.
E13 Additional Rollers For added support; can be installed between standard rollers.
8SP011144 Remote Control Assembly Provides a free-standing control pedestal
with 6 feet of cable in place of the standard mounted controls.
575-3-60 VOLT OPTION If ordering the 575-volt machine, it will be wired for
480-volt operation and a transformer will be provided with the machine. A qualified
electrician will be needed to install the transformer between the power supply and
the machine.
220-1-60 VOLT OPTION A Phase-A-Matic phase converter is shipped with the
machine and requires a qualified electrician to wire it at installation and a 40 AMP
service is required. Price is net price FOB factory to all purchasers. (#8PE19902)
VOLTAGE OPTIONS
Please select ONLY one of the following voltage choices below:
208-3-60 Volt 230-3-60 Volt 460-3-60 Volt 575-3-60 Volt ($1,335) 220-1-60 Volt ($1,950)
Product Short Description Qty List Price Total Price
VT4555 (8-Mark-II) Metal Cutting Band Saw 1 36,700.00 36,700.00
E4 Second Standard Vise (00042) 1 650.00 650.00
Marvel Classic Colors Marvel Classic Color Scheme (Gray with yellow vises and
Marvel logo) 950.00 -
Blade Eagle Beak VTR 3/6 tooth pitch
(in addition to the start-up blade) additional year of parts
warranty when you purchase 10 or more blades. Purchase 36 or
more blades and receive additional year of parts warranty and
up to 35% off parts discount (see blade club flyer for details).
10 Parts 54.00 540.00
Blade Eagle Beak VTR 3/6 tooth pitch for M6 High Column only
(in addition to the start-up blade) additional year of parts warranty when you
purchase 10 or more blades. Purchase 36 or more blades and receive additional
year of parts warranty and up to 35% off parts discount
(see blade club flyer for details). 58.00 -
M6 High Column (8SM6V) 2,250.00 -
M7 High Jaws (in place of standard) (8SM7) 550.00 -
M8 45° High Jaws (in place of standard) (8SE16) 650.00 -
E5 High Jaw Vise- Complete
(in addition to standard) (8SE5) 1,130.00 -
E6 High Jaws - Jaws Only
(in addition to standard) (8SE6) 820.00 -
E15 45° High Jaw Vise - COMPLETE
(in addition to standard) (8SE15) 1,240.00 -
E16 45° High Jaws Only
(in addition to standard) (8SE16) 1,030.00 -
E14 Air Powered Vise (8SE14) 1,050.00 -
M9A Variable Vise Pressure (must order Quantity 1 or 2,
E14 with this for operation of the option) (8AB01288) 890.00 -
M17V 3° Canted Column (Standard Column) (8SM17V) 3,090.00 -
M17HV 3° Canted Column (High Column) (8SM17HV) 4,050.00 -
SP2083 Optional High-Speed Modification (
ONLY 460 VOLT OPERATION) 2,990.00 -
ML2 Mist Lube - Automatic (8SML2) 1,400.00 -
ED2210 Unist Coolube 2210 (price per gallon) 160.00 -
E8 Length Gauge - Machine (8SE8) 250.00 -
8SP01337Alignment Light Laser (8SP01337) 1 1,650.00 1,650.00
8/F055 First Section Dead Roller Conveyor (8SF055) 1,150.00 -
8/X055 Extension Dead Roller Conveyor (8SX055) 830.00 -
SP1118 First Section Free Standing Dead Roller Conveyor
(8SSP1118) 1,070.00 -
8/SP1040 First Section Dead Roller Conv. w/ Manual
Length Gauge (8SSP1040-RH 8FK17173-LF) 5,250.00 -
8/SP1097 Extension Dead Roller Conveyor with
Gauge Rail (8SSP1097) 2,450.00 -
E10 Length Gauge - Assembly (8SE10) 290.00 -
E11 Coolant Pan - Conveyor (8SE11) 420.00 -
E12 Eccentric Lift Roller (8SE12) 330.00 -
E13 Additional Rollers (8SE13) 60.00 -
8SP01144 Remote Control Assembly 3,520.00 -
8SSP7004 Blade Guide Roller Bearing Replaces Standard
(old style) (8SSP7004) 1,130.00 -
575-3-60 Volt Option 1,750.00 -
220-1-60 Volt Option 3,770.00 -
Total Price $39,540.00
MACHINE DELIVERY TIME: At this time availability is estimated to be [17] weeks after
receipt of an approved order.
(Please enter appropriate number in the brackets above)
DISCLAIMER: The estimated ship date from receipt of an order, based on current
production and sales levels as of this quote date is stated above and is subject to
prior orders received.
TERMS OF SALE
All prices contained herein are subject to change without notice and are further subject to an increase in price equal to the amount of any Federal, State, or Local Tax that may be imposed. Amada Machinery America, Inc. also reserves the right to make design changes and/or modifications on machines without prior notice.
Delivery dates given are estimates only, based on prevailing conditions and available information, and any special requirements that may affect the order are subject to the conditions and contingencies beyond our control.
Freight charges are the responsibility of the end user. Amada Machinery America, Inc. will default to ship best way prepaid and added to the invoice unless another method is specified.
A 35% restocking charge will be assessed for all cancelled orders.
No officer, employee, representative, or agent is authorized to bind the company to acceptance of any order in the field. All orders are subject to acceptance by the company.
START-UP SUPPLIES (included with machine at no extra cost):
A. Bandsaw Blade: One (1) high-speed welded-edge Eagle Beak VTR blade 3/6 tooth pitch.
B. Manufacturer’s Technical Data: Two (2) sets consisting of parts listed, operating and maintenance instructions, installation plan, wiring, elementary electric and hydraulic diagrams, and electrical and hydraulic component list.
C. Installation & Operations Video
WARRANTY: Amada Machinery America, Inc. warrants to the original user for a period of (1) year on parts and (2) years on labor from the date of factory shipment, that every new Amada Machinery America, Inc. metal sawing machine is free from defect in material and workmanship. During that period, we will, at our option, repair or replace any part which, upon examination, we find defective. This warranty will not apply to alterations or modifications made upon Amada Machinery America, Inc. metal sawing machines without our written consent, or to machines which have been subject to willful abuse.
Amada Machinery America, Inc. manufactures band saws intended for metal cutting applications, utilizing conventional band saw blades. Although other applications can be foreseen, Amada Machinery America, Inc. cannot be held responsible for any consequences of utilizing equipment outside of its intended design. Amada Machinery America, Inc. band saws are intended for indoor use within operating temperatures of 32 - 104 degrees Fahrenheit. Humidity levels must be below 90% and noncondensing. Air quality is important for cabinet cooling. Amada Machinery America, Inc. takes steps to help filter the air circulating in its enclosures. However, design considerations assume nominal air quality without damaging contaminants such as graphite dust. Machine capacity specifications must also be strictly adhered to.
PURCHASE 10 OR MORE BANDSAW BLADES WITH YOUR INITIAL BANDSAW PURCHASE AND RECEIVE AN ADDITIONAL YEAR OF PARTS WARRANTY.